By Instruction for Installing a Bathtub
By Instruction for Installing a Bathtub
Blog Article
Listed here down the page you will find some incredibly good expertise on the subject of Tools You Need to Install a New Bathtub .
Installing a bathtub isn't exactly rocket science, however it does require strong plumbing, woodworking, and sometimes, tiling abilities. Changing an old bathtub with a new one is likewise a moderately hard project. If the old tub is conveniently obtainable, the project can move immediately; if you have to open up a wall surface to remove the old tub and also place the brand-new bath tub, the task is much harder. In either case, the task is within a residence handyman's abilities, although you will require a helper to leave the old bathtub and also set in the new one. Make sure you have qualified yourself for the job and also fit attempting it. Instead of hiring a service provider to take control of a halfway-completed project, it is far better to take into consideration employing one before you begin. Chances are you may require a professional plumber to make tube connections.
This short article will help you install a new bath tub in your shower room if you have actually already acquired a brand-new tub and also do not need to alter the plan of your previous water pipes.
Your devices and product checklist ought to consist of the following:
Preparing for the Installment
First of all, the supporting frame supplied with the bathroom needs to be fitted (if required) according to the supplier's directions. Next, fit the taps or mixer to the bathtub. When fitting the tap block, it is necessary to make sure that if the tap features a plastic washing machine, it is fitted between the bath and the taps. On a plastic bath, it is also sensible to fit a sustaining plate under the taps system to stop stress on the tub.
Fit the adaptable tap ports to the bottom of the two faucets making use of 2 nuts and olives (in some cases provided with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet opening, and afterwards pass the outlet with the hole in the bathroom. Make use of the nut provided by the producer to fit the plug-hole. Take a look at the plug-hole outlet for an inlet on the side for the overflow pipe.
Next, fit the end of the versatile overflow pipe to the overflow outlet. After that, screw the pipeline to the overflow face which ought to be fitted inside the bath. See to it you use all of the supplied washing machines.
Connect the trap to the bottom of the waste outlet on the bath tub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the catch to the outlet. Attach all-time low of the overflow tube in a similar manner.The bathroom need to currently prepare to be suited its last setting.
Removing Old Taps
If you require to replace old taps with brand-new ones as a part of your setup, then the first thing you need to do is separate the supply of water. After doing so, activate the taps to drain pipes any type of water continuing to be in the system. The procedure of removing the existing faucets can be rather troublesome because of the restricted access that is usually the case.
Make use of a container wrench (crowsfoot spanner) or a tap device to reverse the nut that connects the supply pipelines to the taps. Have a towel prepared for the continuing to be water that will originate from the pipelines. When the supply pipes have been eliminated, make use of the very same device to loosen the nut that holds the faucets onto the bath/basin. You will require to quit the solitary faucets from turning during this procedure. As soon as the taps have actually been gotten rid of, the holes in the bath/basin will have to be cleaned of any kind of old securing substance.
Before going on to fit the brand-new taps, contrast the pipe connections on the old taps to the new taps. If the old faucets are longer than the new faucets, then a shank adapter is needed for the brand-new taps to fit.
Setting up the Bath tub
Utilizing the two wood boards under its feet, position the bathtub in the needed setting. The wood boards are useful in uniformly spreading the weight of the tub over the area of the boards instead of concentrating all the weight onto 4 little factors.
The next objective is to guarantee that the bathtub is leveled all round. This can be attained by inspecting the spirit level and adjusting the feet on the tub until the level reviews degree.
To install faucets, fit all-time low of the furthest flexible faucet port to the appropriate supply pipeline by making a compression sign up with; after that do the same for the various other faucet.
Activate the water supply and inspect all joints and brand-new pipework for leaks and also tighten them if required. Fill up the bathtub and additionally check the overflow outlet and the regular electrical outlet for leaks.
Lastly, deal with the bath paneling as described in the manufacturer's user's manual. Tiling as well as sealing around the bathtub must wait until the tub has actually been made use of at the very least when as this will certainly resolve it right into its final setting.
Fitting New Taps
If the tails of the brand-new faucets are plastic, after that you will need a plastic port to avoid damage to the thread. One end of the adapter fits on the plastic tail of the faucet and also the various other end provides a link to the existent supply pipes.
If you require to fit a monobloc, after that you will certainly require minimizing couplers, which attaches the 10mm pipe of the monobloc to the basic 15mm supply pipeline.
Next, position the tap in the placing hole in the bath/basin ensuring that the washing machines are in location in between the tap and also the sink. Safeguard the tap in position with the maker supplied backnut. Once the faucet is safely in position, the supply pipelines can be attached to the tails of the taps. The taps can either be attached by utilizing corrugated copper piping or with normal faucet connectors. The previous kind must be connected to the faucet ends first, tightening up only by hand. The supply pipes can later on be attached to the other end. Tighten both ends with a spanner after both ends have actually been linked.
Tiling Around the Tub
In the area where the bathroom meets the ceramic tile, it is needed to seal the accompanies a silicone rubber caulking. This is essential as the fitting can move sufficient to fracture a stiff seal, creating the water to pass through the wall between the bathroom as well as the tiling, causing complications with wetness as well as possible leakages to the ceiling listed below.
You can choose from a selection of coloured sealants to assimilate your fixtures and fittings. They are marketed in tubes as well as cartridges, and are capable of sealing spaces as much as a size of 3mm (1/8 inch). If you have a larger void to fill up, you can load it with spins of drenched paper or soft rope. Keep in mind to constantly fill up the bathtub with water before sealing, to permit the movement experienced when the bathtub remains in usage. The sealer can fracture fairly early if you do not take into account this movement prior to sealing.
Conversely, ceramic coving or quadrant tiles can be used to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and also reduce to dimension, are additionally easily offered on the marketplace. It is suggested to fit the floor tiles utilizing waterproof or water resistant sticky as well as grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
As a serious reader about A Step-by-Step Guide to Installing a Bathtub, I was thinking sharing that piece of content was worth the trouble. So long as you enjoyed reading our blog posting kindly be sure to pass it around. We value reading our article about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround.
Book An Estimate Now Report this page